Monday, August 10, 2009

Inhale Ethyl Chloride

How to Change a Tire Sitema

This is very basic, not really science is more rubber or change a tire, only to have the necessary tools to work:

What you need:
  • a spare tire (make sure yours is properly inflated)
  • A key cross
  • A Cat Work Gloves
  • A plastic, cardboard and garbage bags

night for tire changes:

  • An emergency triangle reflector lamp
  • A
Your car comes with several of these items, but must ensure before a puncture occurs.

Step 1 - Find a Safe Area:

If you have a flat tire on the road, do not try to change it, especially if you are very close to the roadside. It is very safe to change a tire on the shoulder, because it is like being in the slow lane. Emergency call service. If you are in a quieter way, it is also important to be clear of the traffic. If possible, you have to push the car to a straight part of the road instead of being in a curve. The traffic is better when possible to avoid You can see it coming. Also be sure to choose a site that is flat, which is not tilted and that is land, to be safe when the jack lifting the car.

As soon as I find a good site, put the car in "park" (or in gear if the transmission is manual), set the parking brake and turn signals of danger. If at night, want to put a triangle Emergency reflector to warn other drivers. You should take the keys from the ignition and turn off the car, but be sure not to lose while changing the tire.

Step 2 - Prepare your tools:

If you have a cardboard or plastic, place it on the ground near the tire to be changed for a clean, dry area where work. If has a pair of gloves, wear them to keep their hands clean and protected. The next thing you need is the spare, often located at the bottom of the car's trunk. Consider some of the spare tires are often for temporary use (known as "space saving") in what amounts to a tire shop to replace or repair the tire. Your manual may tell you where exactly to find the spare. The cat will usually be found in the same place where the spare tire. Bring these items to your work area, gloves, lamps (if necessary) and the spare tire (some cats manage all functions as a key cross). Now you are ready to change the tire.

Step 3 - Loosen the lug nuts of the wheel:

Loosen the lug nuts of the tire when the car is in the ground. It's easier after lifting. If the tire has plug would have to remove to remove the studs. You can use the jack or lug wrench to remove. If Briles have some security lock, check your user manual to remove them.
Once the studs are exposed, place the key in and turn them against clockwise to loosen. Give one or two turns, but be sure not to remove them completely. Do the same for everyone.
If one is too tight, help yourself to support the ends of the lug wrench with one foot and one arm. Make sure the lug wrench is secured to stud, before trying this method. Finally if you have a loose oil around, you can apply it on the line of studs, wait a moment and can be moved more easily.

Step 4 - Pick Your Car:

Place the jack under the car and insert the slot in the chassis or indicated support for this effect. Once the cat is high enough to touch the chassis of your car, place it under the designated spot for it (behind the front wheel or in front of the rear wheel, as specified in the manual). Now you can lift your car, turning the jack handle in the direction of clockwise until the tire is 5 or 6 inches above the ground, leaving just enough space for remove the flat tire and put the spare. Be sure not to put hands or feet under the vehicle once it has been lifted.

Step 5 - Remove Tire:

Place nuts in a safe place where they can not lose. To remove the wheel, each wheel firmly grasp and pull straight out. Place the flat tire and slide it under the body or suspension car at the corner where the cat is being used, if the cat slips will still be supported.

Step 6 - Replace the wheel:

Take the spare tire and put it on the drum, trying to match studs into the holes of the wheel. Place each hand tightening only to hold the rim. If your car uses screws Instead of nuts, holes should align with the wheel drum. The press will once the car is down. Fasten the top, so it will be easier to tighten the others.

Step 7 - Lower Your Auto:

Now, turning the cat in the opposite direction, lower the car to the ground. When the weight is no longer on the cat, remove it from under the car, and follow turning the knob until it is completely closed and set aside. you need to fully tighten the lug nuts using your lug wrench in the direction opposite to that used to loosen. Tighten studs diagonally. Repeat with all the studs. Replace the wheel cap (if any), putting one side in place and the other parties getting hit with the hand or fist.

Step 8 - Return to the Road:

After just change the tire, keep your lug wrench. the flat tire, jack and everything else in the trunk and back on the road. If your spare tire is temporary, do not drive at high speeds (up to 60 kilometers) and be sure to replace the soon as possible. It is also a good idea to have a mechanic check the wheel bolts to be sure.

So we have a safe trip and we will avoid the trouble to call torque assistance, start with the mechanics in this blog.

Quiero Fotos De Vajinas

How the Auto Fuel Injection

This time I'm going to explain that behind this system is from the early twentieth century, but that its implementation costs will not be made a lot of promotion. In English means Fuel Injection, but the carburetor is not responsible for that? yes, but there are details that makes the Fuel Injection system as the highest performance.

Thus, both as the Fuel Injection Carburetor work in a precise mixture of air-fuel (14.7 parts air to 1 part fuel), at which point the carburetor fails over time and that it maintains tolerance in mixture adjustment, to allow adjustment, if the mixture is rich (12 to 1) can damage valves and pistons, and if it is very poor (16 to 1) the motor loses strength and may pollute the environment more than they should.




said, the Fuel Injection system has the advantage of having a constant monitoring of sensors placed in strategic sites of the motor, adjust the mixture obeying the program on your computer (located on the board) and the fuel injection will be always accurate, allowing less polluting emissions.



As we see in the diagrams the carburetor is replaced by this system and the engine suffers a few design changes for the placement of the sensors, we see that the function of each sensor and regulators:

kindled in Cold Valve: When the engine is cold, it takes fuel injector system when the engine warms up, goes down, is activated by a switch.





Temperature Sensor: its function is to review the water temperature to the engine after the thermostat, it also functions as a switch turning on or off the electric fan radiator. Http://es.wikipedia.org/wiki/Radiador



Mass Air Sensor: It has a filament inside the bulbs similar to the computer power is applied to the filament and the air passing through the sensor cools, the computer insists on keeping it warm, in response to variations in the voltage, the computer activates the injectors, which spray enough gas for the engine to work, taking account of both the air I walk like gasoline sprayed with the right mix (14.7 parts air to 1 part gasoline)

Air Flow Sensor: Unlike the previous, does not have a filament, it takes the air coming from the outside of it, pushing the door of the air intake, this happens when accelerating, so its function is to measure the incoming air, send the information to the computer and this determines the fuel for which the exact mixture.

position sensor Throat: This sensor also helps the computer to determine the air / fuel mixture, has an electrical connector that receives a reference voltage of the computer, the speed opens the throttle plate comes outside air, causing an alteration in the voltage reference. This is interpreted by the computer program according to the injectors active long enough to achieve the air / fuel mixture accurately.


Crankshaft Position Sensor: Use more than all direct ignition engines http://mecanicavirtual.iespana.es/dis.htm since no dealer has this sensor is responsible for informing the computer when the piston reaches the maximum stroke and this signal is used by the computer in accordance with the ignition module to generate the spark.



Sensor Manifold Absolute Pressure: Measure the vacuum in the intake manifold, helping the computer to determine the amount of gasoline required in different phases.




Oxygen Sensor: This sensor is not receiving power, the contrary is produced, this sensor works only hot, is responsible for smelling the gases of combustion will escape to help monitor the status of the air / fuel mixture if the gas sent to the exhaust are highly polluting or not, produces voltage signal that translates the computer editing mixing and / or advance or retard the ignition timing.


Water Temperature Sensor: This sensor helps fuel consumption by reference to the temperature of the water, remember that a cold engine consumes more fuel than a warm one.





Assistant Air Controller: I have in most cases the Japanese cars (Nissan, Toyota ... etc) enters auxiliary air when the engine is cold.








Well I hope that this description of this system is useful in next post will explain how the Scanner.

Thursday, August 6, 2009

Message To A Christening



.


The soul does not grow on trees, but feeds on our environment, as the body of food. The soul needs to be fed with beautiful views, words that fill ... or who knows the soul kiss. Kissing

soul is know to have patience, understanding, and never judge anyone, just accept people as they are ... Kissing

soul is embraced when alone, when you are sad ... without saying anything, just stand with that hug of support. Kissing

soul, is to sit together when there is no need to talk, when you just need silence, to not ask questions ... Kissing

soul, is to feel other hands that support strengthening the life expectancy and company. Kissing

soul, ie I want to look ... Kissing

soul .... easy, just enough to decide to get off the pedestal of pride that often surrounds us and consumes us. Kissing

soul ... How many of us need that kiss in the soul that never comes?

Saturday, August 1, 2009

How Many Paracetamol Will Kill You

soul Dance like nobody was watching

.


We convince ourselves that life will be better after .... After finishing the race, after getting a job after getting married, after having a baby, and then after having another.

Then we are frustrated because our children are not big enough, and we will be happier when they grow up and stop being children, then we despair because they are young, difficult to treat.

We think we will be happier when they leave the stage.
Then we decided that our life will be complete when our spouse is better off when we have a better car, when we can go on vacation, when we get promotion, when we retire.

The truth is. NO BETTER TIME TO BE HAPPY NOW.

If not now, when? Life is always full of course, challenges.
is best to admit this and decide to be happy now anyway

There is no course, no way to happiness, happiness is the way it is NOW. Treasure every moment you live, and store it more because you shared it with someone special, so special that you carry in your heart and remember that time waits for no one.

So stop waiting until you finish college, until you fall in love, until you find work, until you get married, until you have kids, until they leave home until you get divorced, until you lose those ten kilos, until Friday night or even Sunday morning
, until the spring, summer, autumn or winter, or until you die to decide that there is no better time than just IT, TO BE HAPPY .........

HAPPINESS IS A JOURNEY, NOT A DESTINATION. HOW IT WORKS
IF YOU DO NOT NEED MONEY, LOVE LIKE
've never been hurt, DANCE ...............
Like nobody's watching.